Stucco calculator
Enter the wall area and what you are plastering over. You get the coats, the thickness of each, and the bags of base coat and finish coat separately — at the honest end of the manufacturer’s coverage range.
Inputs
Result
Coverage per 80 lb bag of base coat
QUIKRETE’s Scratch and Brown Base Coat data sheet publishes two things that fit together exactly: a yield of 0.75 ft³ per 80 lb bag, and a coverage range at three thicknesses. Divide the yield by the thickness and you land on the top of every published range. Multiply that by five sixths and you land on the bottom of every one.
| Thickness | Yield ÷ thickness | Less the allowance | As published | Bags per 100 sq ft |
|---|---|---|---|---|
| 1/4 in | 36 | 30 | — | 4 |
| 3/8 in | 24 | 20 | 20–24 | 5 |
| 1/2 in | 18 | 15 | 15–18 | 7 |
| 5/8 in | 14.4 | 12 | — | 9 |
| 3/4 in | 12 | 10 | 10–12 | 10 |
| 7/8 in | 10.3 | 8.6 | — | 12 |
The greyed column is the arithmetic maximum — every cubic foot of mix landing on the wall and staying there. The bold column takes off the 16.7% the manufacturer’s own range allows for waste and for what the lath keys swallow behind the plane you are measuring. Rows without a published range are the same arithmetic at thicknesses the data sheet does not print.
Coats and thickness, by what you are plastering over
| Backing | Coats | First | Second | Third | Total |
|---|---|---|---|---|---|
| Metal or wire lath over framing | 3 | 3/8 in | 3/8 in | 1/8 in | 7/8 in |
| Unit masonry | 2 | 1/2 in | 1/8 in | — | 5/8 in |
| Cast-in-place concrete | 2 | 1/2 in | 1/8 in | — | 5/8 in |
| One-coat system over lath | 2 | 1/4 in | 1/8 in | — | 3/8 in |
Three coats over metal lath, two over masonry, concrete or gypsum (IRC R703.6.2). The 7/8 in over wire lath is measured from the face of the support, so the lath itself sits inside that dimension. For unit masonry the two documents differ: ASTM C926 gives 5/8 in nominal for two-coat work, the IRC table sets the minimum at 1/2 in. This page uses the ASTM figure, which is the thicker of the two.
A three-coat job is three different orders
The scratch and brown coats are the same product at 3/8 in each. The finish coat is a different bag entirely, goes on at 1/8 in, and covers 70 sq ft a bag instead of 20. Adding the thicknesses up and dividing once gives you the wrong mix of products even when the total weight is close.
For 1,000 sq ft over lath that is 50 bags of base coat for the scratch, 50 more for the brown and 15 of finish coat. 115 bags in total, 9,200 lb, which is 4.6 tons of material going up a wall by hand, and about 550 quarts of water to mix the base coats.
The same wall over unit masonry drops to 82 bags, because the base coat is one 1/2 in pass instead of two at 3/8 in. A proprietary one-coat system over lath comes to 57.
What this does not do
- It does not price the job. Stucco is quoted per square foot installed and the rate moves with region, height, access and finish texture. Bags are the part that can be counted honestly.
- It does not count lath, screed or fasteners. Those come off a takeoff of the elevations, not off an area figure, and the accessory list is where stucco estimates usually go wrong.
- It assumes a flat wall. Bands, reveals, arches and heavy textures all use more, and a sprayed finish wastes more than a hand-applied one.
- Coverage is one manufacturer’s. The yield and the range here are QUIKRETE’s. Other brands publish their own and they are not identical; the arithmetic for converting a yield into coverage is the same whichever bag you buy.
- One-coat systems are proprietary and installed under their own evaluation report. The thickness here is indicative; the report for the actual product governs.
Questions
How many bags of stucco do I need for 1,000 square feet?
For a three-coat job over metal lath, about 115 eighty-pound bags: 50 for the scratch coat, 50 for the brown coat and 15 of finish coat. That is roughly 4.6 tons. Over unit masonry it drops to about 82 bags, because the base coat is one half-inch pass instead of two three-eighths passes. Those figures use the realistic end of the published coverage range.
How much does an 80 lb bag of stucco cover?
20 to 24 square feet at 3/8 inch, 15 to 18 at 1/2 inch, and 10 to 12 at 3/4 inch. The high number in each pair is the bag's theoretical yield of 0.75 cubic feet divided by the thickness, with nothing lost. The low number is exactly five sixths of that, which is the allowance for waste and for the material that disappears into the lath keys. Order to the low number.
How thick should stucco be?
Over metal or wire lath, 7/8 inch in three coats: 3/8 scratch, 3/8 brown and 1/8 finish, measured from the face of the support. Over unit masonry or concrete it is two coats, 5/8 inch nominal under ASTM C926, with the IRC table allowing a minimum of 1/2 inch on masonry. Proprietary one-coat systems are thinner and follow their own evaluation report.
Is stucco two coats or three?
Three over metal lath, two over masonry, concrete or gypsum board. That is IRC R703.6.2. The two-coat case works because the backing is already solid and does not need a scratch coat keyed into lath to hold the rest. A one-coat system is a different thing again: a proprietary fibreglass-reinforced base plus a finish, approved under an evaluation report.
How long between stucco coats?
The scratch coat is moist-cured for a minimum of 48 hours and then left a further 48 hours before the brown coat goes on. The brown coat is not applied until the scratch is rigid enough to take it without deforming. The finish coat needs fog misting or similar curing to stop it drying too fast, which matters most in wind, low humidity or above 90°F.
Do I need one layer of building paper under stucco or two?
Two. The code calls for two layers of Grade D paper behind the lath, installed so each forms a separate continuous drainage plane. There is an exception where a single layer is separated from the stucco by a substantially non-water-absorbing layer or a designed drainage space. This is one of the most common stucco inspection failures, and it costs nothing to get right.
Sources
- 2021 International Residential Code, Chapter 7: Wall Covering. International Code Council. Plaster thicknesses, Table R702.1(1); free to read online.
- ASTM C926, application of portland cement-based plaster. ASTM International.
- QUIKRETE stucco data sheet (coverage). QUIKRETE.
Codes are adopted and amended locally. Check the edition in force where you work.
More Concrete calculators
Excavation, trench & cut-and-fill calculator
Dirt to dig for a trench or a pit with the walls laid back to the OSHA slope, what it swells to on the truck, and the cut-and-fill balance.
Asphalt calculator
Tons of hot mix asphalt for a driveway, path or lot, at the industry's 110 lb per square yard per inch, with lifts, base and cost.
Rebar calculator
Rebar for a slab grid: bars each way, lap splices, 20 ft sticks, weight, ties and chairs, plus a rebar weight calculator.
Mortar calculator
Bags of mortar mix for a brick or block wall, from the wall area or the number of units, at Quikrete's published yields.
Self-leveling concrete calculator
How many bags of self-leveler a floor needs, for Quikrete, LevelQuik, Henry, Ardex, Sakrete and Rapid Set, at any thickness.
Concrete calculator
Cubic yards and 40, 60 or 80 lb bags for a slab, footing, post holes or steps, with waste and the ready-mix order.
Concrete block calculator
Blocks or bricks for a wall, with mortar bags, core grout and courses, net of doors and windows.